Benutzer-Werkzeuge

Webseiten-Werkzeuge


hardware:sphairon_ar860e1b_v2

Sphairon Turbolink AR860E1-B V2

ADSL2+ Modem Annex B/U-R2

Network

  • IP: 192.168.254.254
  • Subnet Mask: 255.255.255.0
  • Username: admin
  • Password: xad$l#12

Hardware

PCB

PBC

UART

Connector: JP103
Settings: 38600 Baud, 8n1

Pin Function
1 ?
2 RX
3 TX
4 GND

Firmware

Firmware Version

  • 370.070822b1_55 (Versatel)
  • 370.090511b1 (Versatel)

Serial Console

Startup

Basic POST completed...     Success.
Last reset cause: Hardware reset (Power-on reset)

PSPBoot1.4 rev: 1.4.0.4 CN-0
(c) Copyright 2002-2005 Texas Instruments, Inc. All Rights Reserved.

Press ESC for monitor... 1

(psbl)

Booting...
Launching kernel decompressor.
Starting LZMA Uncompression Algorithm.
Copyright (C) 2003 Texas Instruments Incorporated; Copyright (C) 1999-2003 Igor Pavlov.
Compressed file is LZMA format.
Kernel decompressor was successful ... launching kernel.

LINUX started...
Config serial console: ttyS0,38400
Auto Detection OHIO chip
This SOC has MDIX cababilities on chip.
CPU revision is: 00018448
Primary instruction cache 16kb, linesize 16 bytes (4 ways)
Primary data cache 8kb, linesize 16 bytes (4 ways)
Number of TLB entries 16.
Linux version 2.4.17_mvl21-malta-mips_fp_le (root@localhost.localdomain) (gcc version 2.95.3 20010315 (release/MontaVista)) #2 ▒T 8▒▒ 22 17:27:32 CST 2007
Determined physical RAM map:
 memory: 14000000 @ 00000000 (reserved)
 memory: 00020000 @ 14000000 (ROM data)
 memory: 007e0000 @ 14020000 (usable)
On node 0 totalpages: 2048
zone(0): 2048 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line:
calculating r4koff... 00102c00(1059840)
CPU frequency 211.97 MHz
Calibrating delay loop... 211.35 BogoMIPS
Freeing Adam2 reserved memory [0x14001000,0x0001f000]
Memory: 6264k/8192k available (1542k kernel code, 1928k reserved, 99k data, 60k init)
Dentry-cache hash table entries: 1024 (order: 1, 8192 bytes)
Inode-cache hash table entries: 512 (order: 0, 4096 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 2048 (order: 1, 8192 bytes)
Checking for 'wait' instruction...  unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
TI Optimizations: Allocating TI-Cached Memory Pool.
Using 120 Buffers for TI-Cached Memory Pool.
DEBUG: Using Hybrid Mode.
NSP Optimizations: Succesfully allocated TI-Cached Memory Pool.
Initializing RT netlink socket
DEBUG: Starting ksoftirqd with ALWAYS_SOFTIRQ:0x3 NON ALWAYS SOFTIRQ:0xfffffffc.
DEBUG: Starting ksoftirqd with priority:0 policy:0 nice:19.
Starting kswapd
Disabling the Out Of Memory Killer
devfs: v1.7 (20011216) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
pty: 32 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0xa8610e00 (irq = 15) is a 16550A
block: 64 slots per queue, batch=16
Initializing the TI QoS NSP Framework.
DEBUG: Initializing the Network Queue Manager Algorithms.
DEBUG: Initialization of the Translation Unit.
DEBUG: Initializing the LOCAL High Priority Database Module.
DEBUG: Initialization of the LOCAL High Priority Database Module successful..
Succesfully Initialized the TI QoS NSP Framework.
CPMAC Auto Detect Enabled: detected internal PHY .
Error getting CPMAC Configuration params for instance:0
Environment Variable:MACCFG_A not set in bootloader
Setting Default configuration params for CPMAC instance:0

 MAC CFG : Tx Interrupts off , threshold : 20
Default Asymmetric MTU for eth0 1500
TI CPMAC Linux DDA version 1.9 - CPMAC DDC version 0.3
Cpmac: Installed 1 instances.
Cpmac driver is allocating buffer memory at init time.
PPP generic driver version 2.4.1
avalanche flash device: 0x400000 at 0x10000000.
 Amd/Fujitsu Extended Query Table v1.0 at 0x0040
number of CFI chips: 1
Avalanche: No single image format found. Using mtd env variables
Looking for mtd device :mtd0:
Avalanche: Adding a mtd0 image (0xa0000), with size (0x160000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x000a0000-0x00200000 : "mtd0"
Avalanche:      linking partition mtd0: mtd0 -> ../../mtdblock/0
Looking for mtd device :mtd1:
Avalanche: Adding a mtd1 image (0x20000), with size (0x80000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00020000-0x000a0000 : "mtd1"
Avalanche:      linking partition mtd1: mtd1 -> ../../mtdblock/1
Looking for mtd device :mtd2:
Avalanche: Adding a mtd2 image (0x0), with size (0x10000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00000000-0x00010000 : "mtd2"
Avalanche:      linking partition mtd2: mtd2 -> ../../mtdblock/2
Looking for mtd device :mtd3:
Avalanche: Adding a mtd3 image (0x10000), with size (0x10000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00010000-0x00020000 : "mtd3"
Avalanche:      linking partition mtd3: mtd3 -> ../../mtdblock/3
Looking for mtd device :mtd4:
Avalanche: Adding a mtd4 image (0x20000), with size (0x1e0000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00020000-0x00200000 : "mtd4"
Avalanche:      linking partition mtd4: mtd4 -> ../../mtdblock/4
Looking for mtd device :mtd5:
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 512 bind 512)
Linux IP multicast router 0.06 plus PIM-SM
ip_conntrack version 2.0 (64 buckets, 512 max) - 372 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
netfilter PSD loaded - (c) astaro AG
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
Initializing the WAN Bridge.
Please set the MAC Address for the WAN Bridge.
Set the Environment variable 'wan_br_mac'.
MAC Address should be in the following format: xx.xx.xx.xx.xx.xx
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k freed
serial console detected.  Disabling virtual terminals.
console=/dev/tts/0
init started:  BusyBox v0.61.pre (2007.08.22-07:45+0000) multi-call binary
Starting pid 9, console /dev/tts/0: '/etc/init.d/rcS'
Algorithmics/MIPS FPU Emulator v1.5
hostname: No such file or directory
ledcfg: reading Standard Configuration File /etc/led.conf
ledcfg: configured 15 states
Using /lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/drivers/atm/tiatm.o
registered device TI Avalanche SAR
Ohio250(7200/7100A2) detected
DSP binary filesize = 376930 bytes
tn7dsl_init : env var DSL_BIT_TMODE is set
tn7dsl_set_modulation : Setting mode to 0xbf
Texas Instruments ATM driver: version:[7.03.01.00]
insmod: avalanche_usb.o: no module by that name found
Waiting for enter to start '/bin/sh' (pid 38, terminal /dev/tts/0)

Please press Enter to activate this console. SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
resolver: configuration tree:
Sep  8 12:00:11 cfgmgr(sar): oamPingInterval(20)(20)
PVC dB
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
Doing BRCTL ...
addbr br0
Doing BRCTL ...
addbr br1
Sep  8 12:00:12 cfgmgr(resolver): stat successfull for /etc/resolv.conf.
Sep  8 12:00:12 cfgmgr(resolver): Resolver Polling Timer Started succesfully.
Sep  8 12:00:12 cfgmgr(sar): DSL Polling Timer Started succesfully.
Sep  8 12:00:12 cfgmgr(fdb): Firewall NAT service started
Default Asymmetric MTU for br0 1500
Sep  8 12:00:12 Default Asymmetric MTU for br1 1500
cfgmgr(lanbridge0): Bridge Created: br0
Bridge Multicasting for br0 is now Enabled.
Doing BRCTL ...
setfilter br0 0
Doing BRCTL ...
addif br0 eth0
Sep  8 12:00:12 cfgmgr(ddnsclient): updateall_servers : No children found for conn:
Sep  8 12:00:12 cfgmgr(lanbridge1): Bridge Created: br1
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
Bridge Multicasting for br1 is now Enabled.
Doing BRCTL ...
setfilter br1 0
Doing BRCTL ...
stp br0 off
Sep  8 12:00:13 cfgmgr(lanbridge0): Bridge Interface Added: eth0
Doing BRCTL ...
setfilter br0 0
Doing BRCTL ...
stp br1 off
br0: port 1(eth0) entering forwarding state
br0: topology change detected, propagating
Sep  8 12:00:22 cfgmgr(sar): DSL Carrier is down

Enter Busybox

Starting pid 38, console /dev/tts/0: '/bin/sh'


BusyBox v0.61.pre (2007.08.22-07:45+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

#

Some Output

# cat /etc/versions
VERSION=3.7.0
BUILD=T370.070822b1_55
BOARD=AR7RD
FSSTAMP=20070822172846
# cat /proc/version
Linux version 2.4.17_mvl21-malta-mips_fp_le (root@localhost.localdomain) (gcc version 2.95.3 20010315 (release/MontaVista)) #2 ▒T 8▒▒ 22 17:27:32 CST 2007
# ifconfig
br0       Link encap:Ethernet  HWaddr 00:30:54:CE:03:22
          inet addr:192.168.254.254  Bcast:192.168.254.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1  ASYMMTU:1500
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

br1       Link encap:Ethernet  HWaddr 00:00:00:00:00:00
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1  ASYMMTU:1500
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

eth0      Link encap:Ethernet  HWaddr 00:30:54:CE:03:22
          UP BROADCAST MULTICAST  MTU:1500  Metric:1  ASYMMTU:1500
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1  ASYMMTU:0
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

# cat /proc/meminfo
        total:    used:    free:  shared: buffers:  cached:
Mem:   6475776  6021120   454656        0   843776  2027520
Swap:        0        0        0
MemTotal:         6324 kB
MemFree:           444 kB
MemShared:           0 kB
Buffers:           824 kB
Cached:           1980 kB
SwapCached:          0 kB
Active:           2872 kB
Inactive:          904 kB
HighTotal:           0 kB
HighFree:            0 kB
LowTotal:         6324 kB
LowFree:           444 kB
SwapTotal:           0 kB
SwapFree:            0 kB
# lsmod
Module                  Size  Used by
tiatm                 134208   0 (unused)
# cat /etc/passwd
admin:x:0:0:Root,,,:/:/bin/sh
# mount
/dev/mtdblock/0 on / type squashfs (ro)
none on /dev type devfs (rw)
proc on /proc type proc (rw)
ramfs on /var type ramfs (rw)
# cat /proc/kmsg
P for Linux NET4.0.
<6>NET4: Ethernet Bridge 008 for NET4.0
<4>Initializing the WAN Bridge.
<4>Please set the MAC Address for the WAN Bridge.
<4>Set the Environment variable 'wan_br_mac'.
<4>MAC Address should be in the following format: xx.xx.xx.xx.xx.xx
<4>VFS: Mounted root (squashfs filesystem) readonly.
<4>Mounted devfs on /dev
<4>Freeing unused kernel memory: 60k freed
<4>Algorithmics/MIPS FPU Emulator v1.5
<4>registered device TI Avalanche SAR
<4>Ohio250(7200/7100A2) detected
<4>DSP binary filesize = 376930 bytes
<4>tn7dsl_init : env var DSL_BIT_TMODE is set
<4>tn7dsl_set_modulation : Setting mode to 0xbf
<4>Texas Instruments ATM driver: version:[7.03.01.00]
<4>Default Asymmetric MTU for br0 1500
<4>Default Asymmetric MTU for br1 1500
<4>Bridge Multicasting for br0 is now Enabled.
<6>device eth0 entered promiscuous mode
<6>br0: port 1(eth0) entering learning state
<4>Bridge Multicasting for br1 is now Enabled.
<6>br0: port 1(eth0) entering forwarding state
<6>br0: topology change detected, propagating

Firmware Update

****************** NSP Firmware Upgrade ******************
Mounting PROC on /var/proc...OK
Mounting DEV on /var/dev...OK
Pivoting / to /var...OK
Changing work dir to / ...OK
Unmounting /flash/proc...OK
Unmounting /flash/dev...OK
Unmounting /flash...OK
Upgrading flash memory...
FLASH /tmp/fw.bin...
Progress: |********************************|  100%
SETMTDS /tmp/fw.bin : /dev/mtdblock/4.
MTD4 = 0x90020000,0x90200000
MTD1 = 0x90020090,0x9009a000
MTD0 = 0x9009a000,0x90200000
REBOOT.
Restarting system.
hardware/sphairon_ar860e1b_v2.txt · Zuletzt geändert: 2012/01/21 22:09 von pixeldoc